Get Quote
Ongoing Water & Wastewater Projects Under Execution

Live Ongoing Projects by Aquen Fluid

Explore Aquen Fluid projects currently under engineering, manufacturing, installation and commissioning across STP, ETP, RO, DM, UF, OWS, ZLD and water-reuse systems. This page highlights live project categories, capacities, locations, industries and current execution stages.

View Ongoing ProjectsDiscuss Your Project
Live Project Overview

Aquen Fluid Ongoing Projects Show Active ExecutionAcross Water & Wastewater Treatment Sites

This page is focused on Aquen Fluid projects where work is currently in progress. It covers live water and wastewater treatment assignments moving through design review, drawing approval, procurement, manufacturing, dispatch, site installation, pre-commissioning and trial-run stages.

STAGE 01

Current Execution Status

Each project is shown with its current stage so visitors can understand whether the work is in engineering, manufacturing, dispatch, installation, pre-commissioning or trial-run preparation.

STAGE 02

Treatment Technologies Covered

Ongoing work includes sewage treatment, effluent treatment, oil-water separation, RO, DM, UF, filtration, water recycling, reuse and zero liquid discharge solutions.

STAGE 03

Site-Based Coordination

Layouts, piping routes, civil readiness, equipment access, electrical panels, instruments and utility connections are coordinated according to actual site conditions.

STAGE 04

Commissioning-Ready Delivery

Execution is planned around outlet quality, reuse goals, compliance norms, hydraulic performance, operator safety and long-term serviceability after handover.

How Ongoing Projects Move Forward

How Aquen Fluid Tracks Live Treatment Projects from Site Study to Commissioning

Every ongoing project follows a controlled workflow from site study to commissioning readiness. The treatment process and equipment package are finalized according to inlet quality, flow load, site space, reuse target, discharge requirement and utility availability.

Step 01

Site Survey & Inlet Data Review

Water, sewage or effluent samples, flow variation, peak load, oil & grease, COD/BOD, TDS, hardness, silica and reuse targets are reviewed before finalizing the execution approach.

Step 02

Process Route Finalization

The treatment line is selected as per application — screening, equalization, biological treatment, clarification, pressure filtration, activated carbon, softening, UF, RO, DM, MEE or ZLD where required.

Step 03

Engineering, BOM & Manufacturing

P&ID, GA drawings, tank sizing, pressure vessels, pumps, blowers, dosing systems, valves, instruments, MCC/PLC panels and skid assemblies are prepared and manufactured under quality checks.

Step 04

Dispatch, Site Installation & Piping

Equipment is dispatched stage-wise and installed with interconnecting piping, cable routing, dosing connections, utility tie-ins, platform access and safety clearances as per approved layout.

Step 05

Pre-Commissioning & Trial Run

Hydro testing, flushing, electrical loop checks, dry run, wet run, dosing calibration, membrane protection, biological seeding and automation logic checks are completed before performance trials.

Step 06

Performance Stabilization & Handover

The plant is stabilized for outlet quality, flow rate, pressure, recovery, sludge handling and operator readiness before handover with O&M guidance and service support.

Ongoing Project Focus Areas

Live Treatment Projects Planned for Compliance, Reuse and Reliable Operation

For Aquen Fluid, an ongoing project is not only material movement; it is controlled progress across engineering, manufacturing, installation quality, testing and operational readiness.

From process approval to manufacturing, site erection and pre-commissioning, Aquen Fluid focuses on hydraulic balance, treatment efficiency, automation logic, safety access and long-term plant reliability.

Ongoing STP, ETP, OWS, RO, DM, UF, ZLD and filtration projects are configured to meet discharge, reuse, process-water or recycling targets based on actual application requirements.

01

Compliance-Focused Treatment Output

Correct pump sizing, pressure loss control, dosing optimization, membrane protection and instrumentation help reduce power use, chemical waste and operating instability.

02

Energy & Chemical Efficiency

Plants are planned with service access for valves, pumps, blowers, filters, membranes, dosing tanks, instruments and electrical panels so maintenance teams can work safely after commissioning.

03

Serviceable Plant Layout

Plants are planned with access for valves, pumps, blowers, filters, membranes, dosing tanks, instruments and electrical panels so maintenance teams can work safely and quickly.